Investigations of hot-dip galvanized dual-phase steel (DP600+Z) sheet metal on selectively oxidized tool steel surfaces under dry deep-drawing conditions

authored by: Simon Schöler, André Langohr, Fahrettin Özkaya, Kai Möhwald, Bernd Arno Behrens, Hans Jürgen Maier
Abstract: As reported in previous studies conducted within the priority program 1676 “Dry forming - Sustainable production through dry machining in metal forming”, selectively oxidized tool surfaces represent a promising approach for the realization of a dry forming process. For the transfer of the findings to an actual industrial deep drawing process, the choice of sheet material is of great importance. The present study reports investigations on hot-dip galvanized dual-phase steel that was deep-drawn with selectively oxidized tools made from hardened 1.2379 tool steel. The data are compared to the deep-drawing behavior of electrolytically galvanized deep-drawing steel, which was used as a reference. The applied oxide system consisted of α-Fe₂O₃ and was generated in a tailored atmosphere with controlled partial pressure of oxygen. A specially developed modular deep-drawing tool was used for the deep-drawing tests, which allowed carrying out cup-drawing tests in which parts of the drawing ring featured different oxidation conditions. The differently set load cases on the drawing ring were then evaluated and examined with respect to the resulting surface properties of the component produced. The changes in the surface morphology prior to and after deep drawing were analyzed using high resolution analysis and the interactions between tool coating and sheet metal were examined. The results obtained provided information about the deep-drawing properties of the sheet metal materials and confirmed the advantages of α-Fe₂O₃ tool coating used as a low-friction separating layer for use in dry deep drawing.
Organisation(s): Institute of Materials Science
Institute of Metal Forming and Metal Forming Machines
Type: Article
Journal: WEAR
Volume: 484-485
ISSN: 0043-1648
Publication date: 15.11.2021
Publication status: Published
Peer reviewed: Yes
ASJC Scopus subject areas: Condensed Matter Physics, Mechanics of Materials, Surfaces and Interfaces, Surfaces, Coatings and Films, Materials Chemistry
Electronic version(s): https://doi.org/10.1016/j.wear.2021.203742 (Access: Closed)
: Details in the research portal "Research@Leibniz University"

BibTeX

@article{83304bd94c4449059e383b129c092c02,
title = "Investigations of hot-dip galvanized dual-phase steel (DP600+Z) sheet metal on selectively oxidized tool steel surfaces under dry deep-drawing conditions",
abstract = "As reported in previous studies conducted within the priority program 1676 “Dry forming - Sustainable production through dry machining in metal forming”, selectively oxidized tool surfaces represent a promising approach for the realization of a dry forming process. For the transfer of the findings to an actual industrial deep drawing process, the choice of sheet material is of great importance. The present study reports investigations on hot-dip galvanized dual-phase steel that was deep-drawn with selectively oxidized tools made from hardened 1.2379 tool steel. The data are compared to the deep-drawing behavior of electrolytically galvanized deep-drawing steel, which was used as a reference. The applied oxide system consisted of α-Fe2O3 and was generated in a tailored atmosphere with controlled partial pressure of oxygen. A specially developed modular deep-drawing tool was used for the deep-drawing tests, which allowed carrying out cup-drawing tests in which parts of the drawing ring featured different oxidation conditions. The differently set load cases on the drawing ring were then evaluated and examined with respect to the resulting surface properties of the component produced. The changes in the surface morphology prior to and after deep drawing were analyzed using high resolution analysis and the interactions between tool coating and sheet metal were examined. The results obtained provided information about the deep-drawing properties of the sheet metal materials and confirmed the advantages of α-Fe2O3 tool coating used as a low-friction separating layer for use in dry deep drawing.",
keywords = "Deep drawing, Dry metal forming, Surface analysis, Tool steel, Tribology",
author = "Simon Sch{\"o}ler and Andr{\'e} Langohr and Fahrettin {\"O}zkaya and Kai M{\"o}hwald and Behrens, {Bernd Arno} and Maier, {Hans J{\"u}rgen}",
note = "Funding Information: Financial support of this study by the German Research Foundation (DFG) (grants no. BE1690/170-2 and MA1175/41-2) within the framework of the priority program Sustainable Production through Dry Processing in Metal Forming (SPP 1676) is gratefully acknowledged.",
year = "2021",
month = nov,
day = "15",
doi = "10.1016/j.wear.2021.203742",
language = "English",
volume = "484-485",
journal = "WEAR",
issn = "0043-1648",
publisher = "Elsevier BV",
}